Auto-meter 1302 User Manual download pdf (Page 2)

SIG.

+12V

LAMP

GND

LAMP

OUT

+12V

To ground (-) negative

Light wire - dash lighting

circuit or 12 Volt (+)

Grommet

To +12 V

ignition source

GND

Back of

speedometer

Sine

Wave

2 Wire

Sender

GND

SIG.

+12V

LAMP

GND

LAMP

OUT

+12V

SIG.

+12V

LAMP

GND

LAMP

OUT

+12V

White (SQ)

To ground (-) negative

Light wire - dash lighting

circuit or 12 Volt (+)

Grommet

To +12 V ignition source

7/8-18 thread

Remove cap for cruise

control cable, otherwise

leave cap installed.

Transmission

take-off

GND

Red (+12 V)

Black (GND)

3-Wire Sender

Back of

speedometer

Drive Key

Supplied with .104 sq x .104 sq

GND

SIG.

+12V

LAMP

GND

LAMP

OUT

+12V

FOR SERVICE CONTACT: AUTO METER PRODUCTS Inc. 413 W. Elm St., Sycamore, IL 60178 USA (815)899-0801 or

Email us at [email protected]

2650-1184 7/24/06

12 MONTH LIMITED WARRANTY

Products that fail within this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that the

product failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty

exceed the original purchase price of the Auto Meter instruments nor shall Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred

due to the failure of this product. Warranty claims to Auto Meter must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the

original purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12 month warranty period. Breaking the instrument seal, improper

use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter Products, Inc. disclaims any liability for consequential damages

due to breach of any written or implied warranty on all products manufactured by Auto Meter.

Wiring

Auto Meter Hall-Effect senders (Square Wave)

- Models 5291 (standard 7/8-18 thread) & 5292 (For Plug in Sensor), 3 wire sender, cruise.

Most OEM style or Factory Installed, 2 wire senders (Sine Wave)

IMPORTANT

When using most OEM/factory

installed (2 wire) senders, you

must calibrate the speedometer

before it will function properly.

WARNING

This speedometer is not recommended

for vehicles with solid core ignition wires

Use 20 AWG stranded or

heavier wire for hook-up

Use 20 AWG stranded or

heavier wire for hook-up

NOTE: This speedometer provides an output (OUT) terminal that can

be used with late model vehicle installations using the existing Vehicle

Speed Sensor (VSS). In these installations, the VSS signal wire should

be connected to the SIG terminal of the speedometer only. The OUT

terminal should then be connected to where the VSS output was

originally wired. This will provide a buffered VSS signal to the PCM/

computer in the vehicle.

To PCM/

Computer

(see Note)

To PCM/

Computer

(see Note in

above section.)

SERVICE

For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you need the

product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after receiving it. ($10.00 charge will be added to the

cost of “RUSH REPAIR.”) If you are sending product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.

1 2

Comments to this Manuals

No comments

Auto-meter 1302 User Manual Page 2

Comments to this Manuals

Related products and manuals for For the car Auto-meter 1302